Вы здесь: infocisco / Тесты Cisco / Тесты Cisco CCNA Exploration 2 / Тесты Cisco CCNA Exploration 2 Chapter 3
Тесты Cisco Exploration 2 Chapter 3

Ответы на вопросы Cisco CCNA Exploration 2 Chapter 3

Неправильные ответы я не перевожу, так как в них может находиться нелогичный смысл.
Перевод помечен зеленым цветом, пояснение - синим.
1. What will be the result of the following commands?
ORL(config)# interface fastethernet 0/0
ORL(config-if)# ip address 172.16.3.1 255.255.255.0
ORL(config-if)# no shutdown
Какой будет результат выполнения следующих команд?
-The 172.16.3.0 network will be routed by any dynamic routing protocol automatically.
+A routing table entry is made to the 172.16.3.0 network with a code of "C". В таблице маршрутизации создастся запись о сети 172.16.3.0 с кодом «C».
-A static route is required to route traffic to the 172.16.3.0 network.
-The commands will be saved to the startup-configuration.
 
2. Why is fast convergence desirable in networks that use dynamic routing protocols?
Почему в сети, которая использует динамические протоколы маршрутизации, желательно иметь быструю сходимость?
-Routers will not allow packets to be forwarded until the network has converged.
-Hosts are unable to access their gateway until the network has converged.
+Routers may make incorrect forwarding decisions until the network has converged. Пока сеть сходится, роутеры могут создать неправильное решение о передачи данных.
-Routers will not allow configuration changes to be made until the network has converged.
 
3. Refer to the exhibit. Router1 and Router2 are running EIGRP. All interfaces are operational and packets can be forwarded between all networks. What information will be found in the routing table for Router1?
Посмотрите на рисунок. На Router1 и Router2 запущен EIGRP. Все интерфейсы работают, и пакеты могут быть переданы между всеми сетями. Какая информация будет найдена в таблице маршрутизации у Router1?
-Router1 will have 6 directly connected networks.
+The administrative distance of the route to network 172.16.0.0 will be 90. Административная дистанция маршрута к сети 172.16.0.0 будет равна 90.
-The metric for routes to 172.16.0.0 will be 1.
-The interface that is used to forward packets to 172.16.0.0 will always be the S0/1 interface.
 
4. Refer to the exhibit. If RIP is the routing protocol, what is the value of the metric from router A to network 192.168.5.0/24?
Посмотрите на рисунок. Если используется протокол маршрутизации RIP, какое будет значение метрики от роутера А к сети 192.168.5.0/24?
+3  
-4
-56
-624
-724
 
5. Which two statements correctly describe the concepts of administrative distance and metric? (Choose two.)
Какие два утверждения правильно описывают концепции административной дистанции и метрики? (Выберите две)
+Administrative distance refers to the trustworthiness of a particular route. Административная дистанция относится к достоверности (надежности) конкретного маршрута.
-A router first installs routes with higher administrative distances.
-The value of the administrative distance can not be altered by the network administrator.
+Routes with the smallest metric to a destination indicate the best path. Маршруты с наименьшей метрикой к пункту назначения указывают на лучший путь.
-The metric is always determined based on hop count.
-The metric varies depending which Layer 3 protocol is being routed, such as IP or IPX.
 
6. Which statement is true regarding routing protocols?
Какое утверждение истинно о протоколах маршрутизации?
-RIP uses hop count and bandwidth as the metric for path selection and sendsupdates periodically.
-OSPF is a Cisco proprietary protocol that sends updates triggered by topology changes.
+EIGRP uses DUAL to calculate the shortest path and can be configured to do unequal cost load balancing. EIGRP использует DUAL для вычисления наикротчайшего пути и может быть сконфигурирован на балансовую передачу данных по маршрутам неравной стоимости.
-BGP is a path vector interior routing protocol.
 
7. The following line of code is present in the routing table:
O 10.16.1.0/27 [110/129] via 192.168.1.5, 00:00:05, Serial0/0/1
What does the number 129 indicate in this output?
Следующая строка кода представлена в таблице маршрутизации: O 10.16.1.0/27 [110/129] via 192.168.1.5, 00:00:05, Serial0/0/1 Что в этой строке показывает число 129?
+The cost for this link has a value of 129. Стоимость этого соединения равняется значению 129.
-The clock rate on this serial interface is set to 129,000.
-The next-hop router is 129 hops away from this router.
-This route has been updated 129 times in this routing table.
 
8. Refer to the exhibit. Which statement correctly describes how R1 will determine the best path to R2?
Посмотрите на рисунок. Какое утверждение правильно описывает, как R1 будет определять наилучший путь к R2?
-R1 will install a RIP route using network A in its routing table because the administrative distance of RIP is higher than EIGRP.
-R1 will install a RIP route using network A in its routing table because the path cost from RIP is lower than EIGRP.
+R1 will install an EIGRP route using network B in its routing table because the administrative distance of EIGRP is lower than RIP. R1 будет использовать маршрут сети B с EIGRP в его таблице маршрутизации, потому что административная дистанция у EIGRP меньше, чем у RIP.
-R1 will install an EIGRP route using network B in its routing table because the path cost from EIGRP is lower than RIP.
-R1 will install an EIGRP route and a RIP route in its routing table and load balance between them.
 
9. Which command would the network administrator issue to determine if load balancing is in effect on a router?
Какую команду введет сетевой администратор для определения – есть ли эффект балансирования передачи данных на роутере.
-show ip protocols
+show ip route  
-show ip interface brief
-show ip interface
 
10. Which two conditions would create a setting where the use of a distance-vector routing protocol would be efficient? (Choose two.)
Какие два состояния создаются, когда используется дистанционно-векторный протокол маршрутизации? (Выберите два)
-the network requires a special hierarchical design
-fast convergence of the network is crucial
+the network is using a hub and spoke topology Сеть состоит из топологии «звезда» (hub and spoke)
+the network is using a flat design У сети простая конструкция
-there are more than 15 hops between the most distant routers
 
11. Which two statements are true regarding classless routing protocols? (Choose two.)
Какие два утверждения верны о бесклассовых протоколах маршрутизации? (Выберите два)
+sends subnet mask information in routing updates В обновлениях маршрутов они отправляют информацию о маске подсети.
-sends complete routing table update to all neighbors
-is supported by RIP version 1
+allows for use of both 192.168.1.0/30 and 192.168.1.16/28 subnets in the same topology позволяют использовать одновременно 192.168.1.0/30 и 192.168.1.16/28 подсети в одной и той же топологии.
-reduces the amount of address space available in an organization
 
12. Which of the following best describes the operation of distance vector routing protocols?
Что из перечисленного ниже наилучшим образом описывает работу дистанционно-векторных протоколов?
-They use hop count as their only metric.
-They only send out updates when a new network is added.
+They send their routing tables to directly connected neighbors. Они отправляют свою таблицу маршрутизации к прямо подключенным соседям.
-They flood the entire network with routing updates.
 
13. When multiple routing protocols have a route to the same destination network, what determines which route is installed in the routing table?
Когда у нескольких протоколов маршрутизации имеется маршрут к одной и той же сети назначения, то, что определяет, какой маршрут будет установлен в таблицу маршрутизации?
-best metric
-lowest hop count
-greatest available bandwidth
+lowest administrative distance Наименьшая административная дистанция
-lowest cost
 
14. Which of the following is associated with link-state routing protocols?
Что из перечисленного ниже ассоциируется с протоколами маршрутизации по состоянию канала (link state)?
-low processor overhead
-poison reverse
-routing loops
-split horizon
+shortest-path first calculations Высчитывание кратчайшего пути
 
15. Which of the following conditions must be met in order for a network to have converged?
Какие из следующих условий должны быть выполнены для того, чтобы сеть сошлась (конвергировалась)?
-The routers in the network are operating with dynamic routing protocols.
-The routers in the network are operating with compatible versions of IOS.
-The routers in the network are operating with the same routing tables.
+The routers in the network are operating with consistent routing knowledge. Роутеры в сети работают со смешанными знаниями о маршрутах.
 
16. What is the purpose of a routing protocol?
Какая цель у протокола маршрутизации?
-It is used to build and maintain ARP tables.
-It provides a method for segmenting and reassembling data packets.
-It allows an administrator to devise an addressing scheme for the network.
+It allows a router to share information about known networks with other routers. Он позволяет роутеру обмениваться информацией об известных сетях с другими роутерами.
-It provides a procedure for encoding and decoding data into bits for packet forwarding.
 
17. Which two statements are true regarding the advantages of the use of static routes? (Choose two).
Какие два утверждения истинны о преимуществах использования статических маршрутов? (Выберите два)
+increased security Повышается безопасность
-reduced effort in configuring routes
+the administrator maintains control over routing Администратор полностью контролирует маршрутизацию.
-easier to implement in a growing network
-reduces the chance of routing errors
-increased router resource usage
 
18. A router learns two paths with equal metrics to a destination network via the RIP routing protocol. How will the router handle packets to the destination network?
Через протокол маршрутизации RIP маршрутизатор узнал о двух сетях с одинаковой метрикой к сети назначения. Как маршрутизатор будет отправлять пакеты к сети назначения?
-The router will install the first route it learned into the routing table.
+The router will install both routes in the routing table and load balance between the two. маршрутизатор установит оба маршрута в таблицу маршрутизации и балансом загрузит пакеты между ними.
-The router will put the first route in the routing table, and denote the second route as a backup route.
-The router will pick the path with the higher bandwidth and will place it in the routing table.
 
19. The following line of code is displayed in a routing table:
R 209.165.201.0/24 [120/2] via 192.168.252.2, 00:00:16, S0/0/0
What can be concluded from this output?
Ниже показана строка кода из таблицы маршрутизации: R 209.165.201.0/24 [120/2] via 192.168.252.2, 00:00:16, S0/0/0 Какое можно сделать заключение из этой строки кода?
-A packet destined for host 192.168.252.2 will be forwarded out the interface connected to network 209.165.201.0/24.
+The value, 120, is used to determine the best path when a router has more than one routing protocol configured for the same destination network. Значение «120» используется для определения наилучшего пути, когда у роутера имеется больше чем один настроенный протокол маршрутизации для той же самой сети назначения.
-This route was manually configured using the ip route command.
-192.168.252.2 is an interface on the router that produced this output.
 
20. An engineer creates a static route by entering the Router(config)# ip route 10.0.0.0 255.255.255.0 192.168.1.2 command. What can be concluded about this route?
Инженер создал статический маршрут введя команду Router(config)# ip route 10.0.0.0 255.255.255.0 192.168.1.2 . Какой можно сделать вывод об этом маршруте?
+The administrative distance of this route is 1. Административная дистанция у этого маршрута будет равна 1.
-192.168.1.2 is the address of an interface on this router.
-This route will display as a directly connected network in the routing table.
-Packets with a destination IP address of 192.168.1.2 will be forwarded to the 10.0.0.0/24 network first.
 
21. Which two statements are true regarding metrics? (Choose two.)
Какие два утверждения истинны касательно метрики? (Выберите два)
-RIP uses bandwidth as a metric.
-OSPF uses delay as a metric.
+EIGRP uses bandwidth as a metric. EIGRP использует пропускную способность как метрику.
+OSPF uses cost based on bandwidth as a metric. OSPF пользуется метрикой-стоимостью, основываясь на пропускной способности.
-RIP uses delay as a metric.
-EIGRP uses hop count only as a metric.
 
22. A growing medium-sized manufacturing company recently began to have routing instability issues. The company uses static routes and has a mixture of over 30 Cisco and non-Cisco routers. The network administrator has decided to convert the network to dynamic routing. What characteristics of protocols should be considered in this selection process?
Растущая средняя производственная компания недавно начала испытывать затруднения в маршрутизации. Компания использует статические маршруты и имеет смесь из 30 Cisco и не Cisco роутеров. Сетевой администратор принимает решение о переводе сети на динамический протокол маршрутизации. Какая характеристика протокола должна учитываться в процессе этого выбора?
-Distance vector routing protocols, such as RIP, converge more quickly than do link-state routing protocols.
-EIGRP can be used on all of the routers in the company.
+OSPF can be used between the routers. Между маршрутизаторами можно использовать OSPF.
-An exterior routing protocol, such as BGP, is recommended for growing companies.
 
Все права защищены. Копирование информации без разрешения автора сайта - запрещено.
infocisco.ru © 2012-2023 eaneav@gmail.com